Key Features
Overview
The Festool 205222 AN-UNI Angle Attachment is a right-angle drill attachment built for compatible Festool cordless drills with the FastFix interface. This is a right-angle drill attachment designed for drilling and screwdriving in narrow places. If you are working inside cabinets, between studs, around joists, or anywhere a full drill body and chuck will not clear, this attachment gives you access without dragging out a separate specialty tool. Model Number: 205222.
What matters here is not just that it turns 90 degrees. It is how fast it helps you keep moving. The FastFix connection lets you swap from one drilling setup to another in seconds, so you can go from standard drilling to close-quarters fastening without breaking your flow. On site, that means less downtime, fewer tool changes, and fewer moments where you are trying to force the wrong setup into a space that is too tight.
Festool also built in quick angle adjustment through the green ring, so you can reposition the attachment without removing it from the drill. That sounds simple, but it is the kind of feature that saves real time when you are lining up screws in awkward corners or trying to keep a bit straight in a cabinet box. The chuck can also rotate 360 degrees without needing to come off the tool, which gives you more control over handle position and bit orientation when space is limited.
The drive side uses a 1/4 inch hex interface with wire detent, and the attachment accepts Festool Centrotec or an adjustable 1/2 inch chuck. In practical terms, that gives you flexibility depending on whether you are drilling pilot holes, running fasteners, or switching between bit styles already in your Festool setup. The FastFix holder keeps this accessory in the same quick-change system Festool users already rely on, which is exactly the point of buying into the platform.
This angle attachment is also rated for a maximum softwood screw size of 3/8 inch x 11-13/16 inch (10 x 300 mm), so it is not just for light-duty trim work. It is made to handle real fastening jobs where torque matters. At about 0.88 lb, it adds capability without turning your drill into something bulky or awkward.
Compatibility is a big part of the story. This accessory is intended for Festool drills equipped with the FastFix system, including models such as TPC 18/4, TDC 18/4, and Festool C and T cordless drills with FastFix holder. Buyers should pay close attention to drill model compatibility before ordering, especially around CXS and TXS references, because source data is not fully consistent there.
Who should buy it? This is a smart add-on for cabinet installers, remodelers, finish carpenters, punch-list pros, and anyone already running Festool drill platforms who regularly works in cramped spaces. If you already own a compatible Festool drill and need right-angle drilling or fastening without carrying a second tool, this attachment makes a lot of sense. If you do not have a FastFix-compatible drill, this is not the accessory to gamble on.
Reach Tight Spaces Without Switching Tools
This accessory is all about access. When a standard drill and chuck cannot fit straight on a fastener or hole location, the right-angle head lets you keep working with the tool platform you already use.
- Quick adjustment ring changes position without removing the attachment from the drill
- 360 degree chuck rotation helps you line up bits and fasteners in awkward working positions
What’s in the Box
- (1) Festool AN-UNI Angle Attachment
Drill, Centrotec chuck, and adjustable 1/2 inch chuck are not included unless separately stated by the seller.
Key Specifications
| Tool Type | Angle Attachment |
|---|---|
| Holder | FastFix |
| Drive Size | 1/4 in Hex |
| Chuck Acceptance | Festool Centrotec or adjustable 1/2 in chuck |
| Max. Screw Size for Softwood | 3/8 in x 11-13/16 in (10 x 300 mm) |
| Weight (lbs) | 0.88 lbs |
| Rotation | 360 degree chuck rotation |
| Made In | Czech Republic |
Compatibility
Built For
Pro Tip
If you are driving fasteners in a cabinet corner or between framing members, set the attachment angle before you get into the space. The green ring lets you fine-tune position fast, but starting with the bit already lined up saves a lot of hand fighting once clearance disappears.
Warranty & Support
Tool Nut’s Take
Festool 205222 AN-UNI Angle Attachment Is the Smart Buy for Tight Access Work
If you already run a compatible Festool drill, this is the clean way to gain right-angle drilling and fastening without carrying another dedicated tool.
- Who it’s for: Festool users doing cabinet work, remodeling, finish work, and service jobs where a normal drill setup will not physically fit.
- Why it stands out: FastFix changeover, quick angle adjustment, and 360 degree chuck rotation make it more useful than a basic fixed-angle attachment.
- Worth knowing: Compatibility is the whole game here, so check your exact drill model before you buy, especially if you use a CXS or TXS platform.
Common Questions
- What is this accessory used for? It is used for right-angle drilling and screwdriving in narrow or hard-to-reach spaces.
- How does it connect to the drill? It uses Festool’s FastFix holder or FastFix interface on compatible Festool cordless drills.
- Can the chuck position be adjusted? Yes. The angle can be adjusted with the green ring, and the chuck rotates 360 degrees without removing it from the drill.
- What bit or chuck setups does it work with? It uses a 1/4 inch hex drive and accepts Festool Centrotec or an adjustable 1/2 inch chuck.
Reviews
There are no reviews yet.